609 609 105609 609 104

Haulotte error codes

Haulotte Optimum 8 (Optimum 1931 E): electric scissor lift, newer generation

The code Fxx.yy is shown on the machine's display and in the Haulotte Diag app. Older Optimum machines with a ZAPI controller give AL alarms; these are listed under the system ‘Haulotte: Activ'Screen and ZAPI controllers’. Below are 59 codes with the original message from the manufacturer's manual and its description. They apply to these machines: Haulotte Optimum 8, Optimum 1931 E. Source: Haulotte Maintenance Book Optimum 8 (4001069810), fault codes chapter.

Showing the first 30: type more digits of the code.

The descriptions are quoted from the manufacturer's service documentation and are for guidance only. Clearing codes, calibrations and repairs are carried out by a qualified service technician according to the manual for the specific serial number. A machine with an active blocking code must not be used until the cause has been removed.

All Haulotte codes: the list

CodeMeaningType
F01.01Inverter Masterblocking fault
F01.05Pump failureblocking fault
F01.06Overheatingblocking fault
F01.08Low Batterywarning / function limited
F01.09Electrical park brake 1blocking fault
F01.10Electrical park brake 2blocking fault
F01.11Inverter Slaveblocking fault
F01.12Wrong controller hardwareblocking fault
F02.04Power Contactorblocking fault
F03.15Water refill pump control relaywarning / function limited
F04.01Steeringblocking fault
F04.04Armblocking fault
F04.11Principal movementsblocking fault
F04.40Potholesblocking fault
F04.41Movement Selection valveblocking fault
F05.01Arm/Drive joystickblocking fault
F05.11Joystick neutralblocking fault
F06.01No Loading Cal Calibration requiredwarning / function limited
F07.05Motor temperature sensorwarning / function limited
F07.06Arm Angleblocking fault
F07.21Pressure sensorblocking fault
F07.33Steer angleblocking fault
F07.35Motor encoderblocking fault
F07.36ECU temperatureblocking fault
F07.44Tilt sensor not calibratedwarning / function limited
F07.46Tilt sensor errorblocking fault
F08.04Supplyblocking fault
F08.07Circuit selectorblocking fault
F08.09Common output supplyblocking fault
F08.10Power supplyblocking fault
F08.13Chargerwarning / function limited
F08.16Charger dialogwarning / function limited
F08.19Battery voltage drop too deepwarning / function limited
F10.03Micro drive Overspeedwarning / function limited
F10.14Steering angle not calibratedwarning / function limited
F10.16Arm angle not calibratedwarning / function limited
F10.21Battery water refill systemwarning / function limited
F10.22Battery water refill neededwarning / function limited
F10.24Incoherence between water level in refill tank and water level inwarning / function limited
F11.09Arm incoherenceblocking fault
F12.01CAN Fault Check wiresblocking fault
F12.02E2P Read/Write Error Change calc.blocking fault
F12.04E2P Param Reset Check settingsblocking fault
F12.05E2P Param Not Setblocking fault
F12.07ECU software version incoherenceblocking fault
F12.08ECU fault (master)blocking fault
F12.09ECU fault (slave)blocking fault
F12.10Parameters reload Restart machinewarning / function limited
F12.11Parameters reload Restart machinewarning / function limited
F12.16Internal error of diagnostic system (request) Check diagnostic systemwarning / function limited
F12.17Internal error of diagnostic system (set) Check diagnostic systemwarning / function limited
F13.01Lower Box Switches Check switchesblocking fault
F13.02Platform switches Check switchesblocking fault
F13.10Neutral switch Check chassis switchesblocking fault
F13.11Switches neutral 2 Check plat. switchesblocking fault
F15.06J1939blocking fault
F16.01Overheatingwarning / function limited
F16.02Speed problemblocking fault
F16.03Motor supplyblocking fault