609 609 105609 609 104

Haulotte error codes

Haulotte HA20 LE and HA20 LE PRO (HA61 LE): electric boom lift

The code Fxx.yy is shown on the ground control box display (Activ'Screen) and in the Haulotte Diag app: the first two digits are the system group (e.g. F03 = relays, F04 = solenoid valves, F05 = joysticks, F07 = sensors, F08 = power supply, F09 = engine, F12 = internal controller faults), the last two identify the specific component. Below are 113 codes with the original message from the manufacturer's manual and its description. They apply to these machines: Haulotte HA20 LE, HA20 LE PRO, HA61 LE, HA61 LE PRO. Source: Haulotte Maintenance Book HA20 LE (4001028020), fault codes chapter.

Showing the first 30: type more digits of the code.

The descriptions are quoted from the manufacturer's service documentation and are for guidance only. Clearing codes, calibrations and repairs are carried out by a qualified service technician according to the manual for the specific serial number. A machine with an active blocking code must not be used until the cause has been removed.

All Haulotte codes: the list

CodeMeaningType
F02.02Emergency Pumpblocking fault
F02.04Power Contactor KMPblocking fault
F02.05Heating Relayblocking fault
F03.06Horn Relaywarning / function limited
F03.08Start Relayblocking fault
F03.09Supply / KeySwitch Relblocking fault
F03.11Inverter Relayblocking fault
F03.14Charger Sector Relayblocking fault
F03.15Water refill pump control relaywarning / function limited
F04.01Steeringblocking fault
F04.02Compensationblocking fault
F04.03Turret rotationblocking fault
F04.04Armblocking fault
F04.05Boomblocking fault
F04.06Telescopeblocking fault
F04.07Jibblocking fault
F04.08Cage rotationblocking fault
F04.11Principal movementsblocking fault
F04.33Steering modeblocking fault
F04.34Front Axle Unlockingblocking fault
F05.01Drive Joystickblocking fault
F05.02Arm Joystickblocking fault
F05.04Boom Joystickblocking fault
F05.05Turntable Joystickblocking fault
F05.11Joystick neutralwarning / function limited
F05.12Joystick neutral 2warning / function limited
F05.13Joystick neutral 3warning / function limited
F06.01No Loading Cal Calibrateblocking fault
F06.03Gauges out of Rangeblocking fault
F06.04Incoh Gaugesblocking fault
F06.05Low Power Gauges supplyblocking fault
F06.06Weighing sensorsblocking fault
F06.07Weighing systemblocking fault
F06.08Strong overloadblocking fault
F06.09Negative loadblocking fault
F07.01Low Positionblocking fault
F07.03Boom Angleblocking fault
F07.04Boom Angleblocking fault
F07.06Arm Angleblocking fault
F07.10Teles. Lengthblocking fault
F07.11Teles. Lengthblocking fault
F07.15Compensation Pos.blocking fault
F07.30Engine Oil Pressurewarning / function limited
F07.34Front Axle Unclockingblocking fault
F07.39Fuel level sensorwarning / function limited
F07.40Twilight sensorwarning / function limited
F07.44Tilt sensor not calibratedblocking fault
F07.46Tilt sensorblocking fault
F08.04Calc. Input Supplyblocking fault
F08.05Calc. Input Supplyblocking fault
F08.08Unplugged connectorblocking fault
F08.10High power supplywarning / function limited
F08.12Wheel angle sensorblocking fault
F08.13Chargerwarning / function limited
F08.14Battery Management Systemwarning / function limited
F08.15Thermal sensor of Battery Management Systemwarning / function limited
F09.01Water temperature Engine overheatblocking fault
F09.02Oil pressure Engine pressureblocking fault
F09.07Amber warning lamp Check Enginewarning / function limited
F09.08Red stop lamp Check Engineblocking fault
F09.10D+ Engine alternatorwarning / function limited
F10.17Activ' Lighting Systemwarning / function limited
F10.21Battery water refill systemwarning / function limited
F10.22Battery water refill neededwarning / function limited
F10.24Incohernce between water level in refill tank and water level inwarning / function limited
F11.06Buzzerwarning / function limited
F11.07Container modemessage
F12.01CAN Fault Check wiringblocking fault
F12.02E2P Read / Write Errorblocking fault
F12.04E2P Param Reset Check settingswarning / function limited
F12.05Machine not setblocking fault
F12.10Wrong Internal Parameters Check settingsblocking fault
F12.11Wrong Internal Parameters Check settingsblocking fault
F12.12Wrong Internal Parameters Check settingsblocking fault
F12.13Wrong Internal Parameters Check settingsblocking fault
F12.14Wrong Internal Parameters Check settingswarning / function limited
F12.20Details of the CAN Faultblocking fault
F12.21Details of the CAN Faultblocking fault
F12.22Details of the CAN Faultblocking fault
F12.23Details of the CAN Faultblocking fault
F12.24Details of the CAN Fault (Pump)blocking fault
F12.25Details of the CAN Fault (Generator)blocking fault
F13.01Turret switchesblocking fault
F13.02Platform switchesblocking fault
F13.10Switches neutral Sw.: Lower boxwarning / function limited
F13.11Switches neutral 2 Sw.: Upper boxwarning / function limited
F15.06CANBus Cycle Unit -blocking fault
F16.01Motor overheatingwarning / function limited
F16.02Motor Speed Issueblocking fault
F16.03Power Supply Issueblocking fault
F16.04Brake Issueblocking fault
F16.05Sensor Issuewarning / function limited
F16.06Untreated ZAPI codeblocking fault
F16.07Motor failureblocking fault
F16.08Drive internal failureblocking fault
F16.09Unable to stop the machineblocking fault
F16.10Motor failureblocking fault
F17.01Motor overheatingwarning / function limited
F17.02Motor Speed Issueblocking fault
F17.03Power Supply Issueblocking fault
F17.04Sensor Issuewarning / function limited
F17.05Untreated ZAPI codeblocking fault
F17.06Fail to reach min speedwarning / function limited
F17.07Motor failureblocking fault
F17.08Internal failureblocking fault
F18.01Motor overheatingblocking fault
F18.02Motor Speed Issueblocking fault
F18.03Power Supply Issueblocking fault
F18.04Sensor Issueblocking fault
F18.05Untreated ZAPI codeblocking fault
F18.06Motor failureblocking fault
F18.07Internal failureblocking fault
F18.08Function failureblocking fault