Genie error codes

Genie XC, HF and J boom lifts (S-60 XC, S-80 XC, S-85 XC, S-80 HF, S-85 HF, S-60 J, S-80 J)

The code is made up of two numbers: the fault source and the fault type (e.g. 15-21), shown on the display of the machine's ground control box. Below are 208 codes with the original message from the manufacturer's manual and its description. They apply to these machines: Genie S-60 XC, S-80 XC, S-85 XC, S-80 HF, S-85 HF, S-60 J, S-80 J. Source: Genie Service and Repair Manuals (Part No. 1316494, 1315679, 1288652, 1280490, 1285305, 1285307), Fault Codes section.

Brand

Machine type / control system

Error code

Showing the first 30: type more digits of the code.

The descriptions are quoted from the manufacturer's service documentation and are for guidance only. Clearing codes, calibrations and repairs are carried out by a qualified service technician according to the manual for the specific serial number. A machine with an active blocking code must not be used until the cause has been removed.

All Genie codes: the list

Code	Meaning	Type
1-13	Engine Can Bus — Not detected	blocking fault
6-19	Key switch — Fault	blocking fault
7-21	Engine Warning — Fault	warning / function limited
8-21	Engine Stop — Fault	blocking fault
9-21	Engine — Fault	warning / function limited
10-27	Ground Controls Engine Start Switch — Active at startup	warning / function limited
11-19	Engine Start Toggle Switch — Stuck ON at power up.	warning / function limited
11-27	Platform Controls Engine Start Switch — Active at startup	warning / function limited
12-13	Machine CAN Bus — Not detected	blocking fault
12-29	CAN Bus — System not functioning	blocking fault
13-19	Jib Up/Down Toggle Switch — Stuck ON at power up.	warning / function limited
13-27	Jib Up/Down Switch — Active at startup	warning / function limited
14-15	Alternator — Fault	warning / function limited
15-19	Foot Switch — Stuck ON at power up, or timeout occurred.	warning / function limited
15-27	Foot Switch — Active at startup	warning / function limited
15-28	Foot Switch — Timeout	warning / function limited
17-11	Aux Pump Coil — Shorted to supply voltage	blocking fault
19-12	APU Solenoid and Switch — Solenoid output shorted to V+	blocking fault
19-15	APU Solenoid and Switch — Solenoid output shorted to GND	blocking fault
19-19	APU Solenoid and Switch — Stuck ON at power up.	warning / function limited
19-27	Platform Aux Enable Switch — Active at startup	warning / function limited
20-11	Pri Boom Ext / Ret Joystick — Shorted to supply voltage	blocking fault
20-12	Primary Boom Extend / Retract Joystick — Joystick voltage too high.	blocking fault
20-15	Primary Boom Extend / Retract Joystick — Joystick voltage too low.	blocking fault
20-19	Primary Boom Extend / Retract Joystick — Joystick held at startup.	warning / function limited
20-27	Pri Boom Ext / Ret Joystick — Active at startup	warning / function limited
21-11	Pri Boom Up / Down Joystick — Shorted to supply voltage	blocking fault
21-12	Primary Boom Up / Down Joystick — Joystick voltage too high.	blocking fault
21-15	Primary Boom Up / Down Joystick — Joystick voltage too low.	blocking fault
21-19	Primary Boom Up / Down Joystick — Joystick held at startup.	warning / function limited
21-27	Active at startup	warning / function limited
21-28	startup	warning / function limited
22-11	Pri Boom Up coil — Shorted to supply voltage	blocking fault
22-12	Primary Boom Up Valve — Circuit shorted to V+	blocking fault
22-15	Primary Boom Up Valve — Circuit shorted to GND	blocking fault
23-11	Pri Boom Down Coil — Shorted to supply voltage	blocking fault
23-12	Primary Boom Down Valve — Circuit shorted to V+	blocking fault
23-15	Primary Boom Down Valve — Circuit shorted to GND	blocking fault
24-13	Pri Boom Angle — Not detected	blocking fault
24-14	Pri Boom Angle — Cross check failed	blocking fault
24-17	Pri Boom Angle — Not calibrated	blocking fault
24-19	Pri Boom Angle — Value out of expected range	blocking fault
24-36	Boom Angle Sensor — Internal check	blocking fault
25-21	Cable tension — Fault	blocking fault
26-11	Pri Boom Ext Coil — Shorted to supply voltage	blocking fault
26-12	Primary Boom Extend Valve — Circuit shorted to V+	blocking fault
26-15	Primary Boom Extend Valve — Circuit shorted to GND	blocking fault
27-11	Pri Boom Ret Coil — Shorted to supply voltage	blocking fault
27-12	Primary Boom Retract Valve — Circuit shorted to V+	blocking fault
27-15	Primary Boom Retract Valve — Circuit shorted to GND	blocking fault
35-19	Ground Buttons — Held at startup	warning / function limited
35-27	Ground Control Buttons — Active at startup	warning / function limited
36-11	Jib Up Coil — Shorted to supply voltage	blocking fault
36-12	Jib Up Valve — Circuit shorted to V+	blocking fault
36-15	Jib Up Valve — Circuit shorted to GND	blocking fault
37-11	Jib Down Coil — Shorted to supply voltage	blocking fault
37-12	Jib Down Valve — Circuit shorted to V+	blocking fault
37-15	Jib Down Valve — Circuit shorted to GND	blocking fault
40-11	Jib Select Coil — Shorted to supply voltage	blocking fault
41-11	Turntable Rotate Joystick — Shorted to supply voltage	blocking fault
41-12	Turntable Rotate Joystick — Joystick voltage too high.	blocking fault
41-15	Turntable Rotate Joystick — Joystick voltage too low.	blocking fault
41-19	Turntable Rotate Joystick — Joystick held at startup.	warning / function limited
41-27	Turntable Rotate Joystick — Active at startup	warning / function limited
42-11	Turntable Rotate CW Coil — Shorted to supply voltage	blocking fault
42-12	Turntable Rotate CW Valve — Circuit shorted to V+	blocking fault
42-15	Turntable Rotate CW Valve — Circuit shorted to GND	blocking fault
43-11	Turntable Rotate CCW Coil — Shorted to supply voltage	blocking fault
43-12	Turntable Rotate CCW Valve — Circuit shorted to V+	blocking fault
43-15	Turntable Rotate CCW Valve — Circuit shorted to GND	blocking fault
44-19	Drive Enable Switch — Stuck ON at power up.	warning / function limited
44-27	Drive Enable Toggle Switch — Active at startup	warning / function limited
45-19	Platform Level Up/Down Switch — Stuck ON at power up.	warning / function limited
45-27	Platform Level Toggle Switch — Active at startup	warning / function limited
46-11	Platform Rotate CW Coil — Shorted to supply voltage	blocking fault
46-12	Platform Rotate CW Valve — Circuit shorted to V+	blocking fault
46-15	Platform Rotate CW Valve — Circuit shorted to GND	blocking fault
47-11	Platform Rotate CCW Coil — Shorted to supply voltage	blocking fault
47-12	Platform Rotate CCW Valve — Circuit shorted to V+	blocking fault
47-15	Platform Rotate CCW Valve — Circuit shorted to GND	blocking fault
51-11	Drive Joystick — Shorted to supply voltage	blocking fault
51-12	Drive Forward / Reverse Joystick — Joystick voltage too high.	blocking fault
51-15	Drive Forward / Reverse Joystick — Joystick voltage too low.	blocking fault
51-19	Drive Forward / Reverse Joystick — Joystick held at startup.	warning / function limited
51-27	Drive Joystick — Active at startup	warning / function limited
52-11	Drive Forward Pump Coil — Shorted to supply voltage	blocking fault
52-12	Drive Forward Valve — Circuit shorted to V+	blocking fault
52-15	Drive Forward Valve — Circuit shorted to GND	blocking fault
53-11	Drive Reverse Pump Coil — Shorted to supply voltage	blocking fault
53-12	Drive Reverse Valve — Circuit shorted to V+	blocking fault
53-15	Drive Reverse Valve — Circuit shorted to GND	blocking fault
54-11	Brake Release Coil — Shorted to supply voltage	blocking fault
54-12	Brake Release Valve — Circuit shorted to V+	blocking fault
54-15	Brake Release Valve — Circuit shorted to GND	blocking fault
55-11	High Drive Speed Coil — Shorted to supply voltage	blocking fault
55-12	Motor Stroke Valve — Circuit shorted to V+	blocking fault
55-15	Motor Stroke Valve — Circuit shorted to GND	blocking fault
56-13	Telematics Device — Not detected	message
61-11	Steer Joystick — Shorted to supply voltage	blocking fault
61-12	Steer Joystick — Joystick voltage too high.	blocking fault
61-15	Steer Joystick — Joystick voltage too low.	blocking fault
61-19	Steer Joystick — Joystick held at startup.	warning / function limited
61-27	Steer Joystick — Active at startup	warning / function limited
62-27	Prox Override Toggle Switch — Active at startup	warning / function limited
68-21	Safety Envelope Fault — Out of range	blocking fault
68-27	Ground Function Enable Button — Active at startup	warning / function limited
69-11	AC Generator Output — Shorted to supply voltage	blocking fault
69-12	Generator Control Circuit — Circuit shorted to V+	blocking fault
69-15	Generator Control Circuit — Circuit shorted to GND	blocking fault
71-15	ESTOP Circuit — ESTOP Return circuit shorted to GND	blocking fault
71-16	TCON — Fault	blocking fault
71-21	ESTOP Circuit — ESTOP Return circuit mismatch	blocking fault
71-22	ESTOP Circuit — ESTOP Source circuit is shorted to GND	blocking fault
71-31	ESTOP Circuit — ESTOP Source circuit mismatch	blocking fault
72-14	Lift Guard Contact Alarm Switch — Cross check failed	blocking fault
72-21	Lift Guard Contact Alarm Switch — Fault	blocking fault
72-36	Contact Alarm — Switch state mismatch	blocking fault
73-12	Engine Oil Pressure — Sensor value too high	blocking fault
73-24	Engine Oil Pressure — Too low	blocking fault
74-15	Engine Temperature — Sensor value too low	blocking fault
74-23	Engine Temperature — Too high	blocking fault
75-34	TCON Secondary Processor Software — Incorrect software version	blocking fault
76-13	Platform Load Sensor — Not detected	blocking fault
76-14	Platform Load Sensor — Cross check failed	blocking fault
76-15	Platform Load Sensor — Value to low	blocking fault
76-17	Platform Load Sensor — Not calibrated	blocking fault
76-21	Platform Load Sensor — Fault	blocking fault
77-21	Platform Overload Detection — Internal check	blocking fault
78-13	Platform Controller (PCON) — Not detected	blocking fault
78-29	Platform Controller (PCON) — Software version mismatch	blocking fault
78-34	Platform Controller (PCON) — Incorrect software version	blocking fault
78-36	Platform Controller (PCON) — Secondary processor not detected.	blocking fault
79-13	Display Controller (DISCON) — Not detected	blocking fault
79-29	Display Controller (DISCON) — Software version mismatch	blocking fault
79-34	Display Controller (DISCON) — Incorrect software version	blocking fault
80-13	Turntable Controller (TCON) — Not detected	blocking fault
80-20	Turntable Controller (TCON) — Remote disable	blocking fault
80-29	Turntable Controller (TCON) — Software version mismatch	blocking fault
80-36	Turntable Controller (TCON) — Incorrect software version	blocking fault
82-21	Overload — Recovery	message
83-20	Disabled — By owner	blocking fault
83-21	Disabled — By owner	blocking fault
84-13	Chassis Angle — Not detected	blocking fault
84-17	Chassis Angle — Not calibrated	blocking fault
84-21	Chassis Angle — Turntable Tilt Sensor Internal Error.	blocking fault
85-13	Chassis Angle Safety — Not detected	blocking fault
88-11	Function Enable Coil — Shorted to supply voltage	blocking fault
88-12	Function Enable Valve — Circuit shorted to V+	blocking fault
88-15	Function Enable Valve — Circuit shorted to GND	blocking fault
89-12	Fuel Level Sensor — Value to high	message
89-15	Fuel Level Sensor — Value to low	message
92-11	Turntable Rotate Flow Coil — Shorted to supply voltage	blocking fault
92-12	Turntable Rotate Flow Valve — Circuit shorted to V+	blocking fault
92-15	Turntable Rotate Flow Valve — Circuit shorted to GND	blocking fault
94-13	Primary Boom Length — Not detected	blocking fault
94-14	Primary Boom Length — Cross check failed	blocking fault
94-17	Primary Boom Length — Not calibrated	blocking fault
94-19	Primary Boom Length — Value out of expected range	blocking fault
94-36	Boom Length Sensor — Internal check	blocking fault
95-13	Engine RPM Not Detected — Not detected	blocking fault
96-21	Engine Oil Pressure — Value too low	blocking fault
98-10	Platform Level Angle — Envelope exceeded	blocking fault
98-13	Platform Level Angle — Not detected	blocking fault
98-14	Platform Level Angle — Cross Check Fault	blocking fault
98-17	Platform Level Angle — Not calibrated	blocking fault
98-19	Platform Level Angle — Out of range	blocking fault
99-11	Primary Boom Extend / Retract Flow Coil — Shorted to supply voltage	blocking fault
100-11	Platform Level Up Coil — Shorted to supply voltage	blocking fault
100-12	Platform Level Up Valve — Circuit shorted to V+	blocking fault
100-15	Platform Level Up Valve — Circuit shorted to GND	blocking fault
101-11	Platform Level Down Coil — Shorted to supply voltage	blocking fault
101-12	Platform Level Down Valve — Circuit shorted to V+	blocking fault
101-15	Platform Level Down Valve — Circuit shorted to GND	blocking fault
110-27	Platform Rotate Toggle Switch — Active at startup	warning / function limited
116-13	Model Configuration — Model Config Not Detected	blocking fault
116-31	Model Configuration — Setup invalid	blocking fault
141-10	Boom — Safety Envelope Exceeded	blocking fault
150-11	Sensor Power P26PWR — Shorted to supply voltage	blocking fault
150-21	Platform Overload Recovery — Condition occurred	warning / function limited
152-11	Primary Boom Up/Down Flow Coil — Shorted to supply voltage	blocking fault
152-12	Primary Boom Up/Down Flow Valve — Circuit shorted to V+	blocking fault
152-15	Primary Boom Up/Down Flow Valve — Circuit shorted to GND	blocking fault
160-11	LF Steer Coil — Shorted to supply voltage	blocking fault
160-12	Steer Left Valve — Circuit shorted to V+	blocking fault
160-15	Steer Left Valve — Circuit shorted to GND	blocking fault
161-11	RF Steer Coil — Shorted to supply voltage	blocking fault
161-12	Steer Right Valve — Circuit shorted to V+	blocking fault
161-15	Steer Right Valve — Circuit shorted to GND	blocking fault
169-12	Primary Boom Extend / Retract Flow Valve — Circuit shorted to V+	blocking fault
169-15	Primary Boom Extend / Retract Flow Valve — Circuit shorted to GND	blocking fault
174-19	Platform Rotate Toggle Switch — Stuck ON at power up.	warning / function limited
177-12	Engine Coolant Temperature — Value too high	blocking fault
178-21	Engine Warning Lamp — Fault	warning / function limited
179-11	Platform Recirculation Coil — Shorted to supply voltage	message
179-21	Engine Stop Lamp — Fault	blocking fault
185-11	ESTOP Source — Shorted to supply voltage	blocking fault
186-11	ESTOP Return — Shorted to supply voltage	blocking fault
187-13	TCON Bank power — Not detected	blocking fault
188-13	PCON Bank power — Not detected	blocking fault
206-13	TCON Bank Power Not Detected PCON Bank Power Not Detected	blocking fault
240-12	Turntable Sensor Power — P85PWR Short to B+	blocking fault
240-15	Turntable Sensor Power — P85PWR Short to B-	blocking fault
241-12	Turntable Sensor Power — P109PWR is shorted to B+	blocking fault
241-15	Turntable Sensor Power — P109PWR is shorted to B-	blocking fault
242-12	Sensor Power P26PWR — Circuit shorted to V+	blocking fault
242-15	Sensor Power P26PWR — Circuit shorted to GND	blocking fault
243-19	Proximity Override Toggle Switch — Stuck ON at power up.	warning / function limited
263-11	Platform Level Loop Coil — Shorted to supply voltage	message