Genie error codes

Genie S-85 XC FE and S-85 XC E (hybrid and electric drive)

The code is made up of two numbers: the fault source and the fault type (e.g. 15-21), shown on the display of the machine's ground control box. Below are 250 codes with the original message from the manufacturer's manual and its description. They apply to these machines: Genie S-85 XC FE, S-85 XC E. Source: Genie Service and Repair Manual S-85 XC FE / E (Part No. 1337498), Fault Codes section.

Brand

Machine type / control system

Error code

Showing the first 30: type more digits of the code.

The descriptions are quoted from the manufacturer's service documentation and are for guidance only. Clearing codes, calibrations and repairs are carried out by a qualified service technician according to the manual for the specific serial number. A machine with an active blocking code must not be used until the cause has been removed.

All Genie codes: the list

Code	Meaning	Type
6-21	Key switch — Fault	blocking fault
15-27	Foot switch — Active at startup	warning / function limited
15-28	Foot switch — Timeout	warning / function limited
16-27	Speed adjustment toggle switch — Active at startup	warning / function limited
17-25	Auxiliary contactor fault — Resistance too high	blocking fault
17-27	Auxiliary contactor fault — Active at startup	blocking fault
18-25	Proportional relief 1 coil — Resistance too high	blocking fault
18-26	Proportional relief 1 coil — Resistance too low	blocking fault
19-27	Auxiliary enable toggle switch — Active at startup	warning / function limited
20-11	Primary boom extend/retract joystick — Shorted to supply	blocking fault
20-16	Primary boom extend/retract joystick — Value at 0 V	blocking fault
20-17	Primary boom extend/retract joystick — Not calibrated	blocking fault
21-11	Pri Boom Up / Down Joystick — Shorted to supply	blocking fault
21-16	Pri Boom Up / Down Joystick — Value at 0 V	blocking fault
21-17	Pri Boom Up / Down Joystick — Not calibrated	blocking fault
22-21	Primary boom up coil — Valve status fault	blocking fault
22-25	Primary boom up coil — Resistance too high	blocking fault
22-26	Primary boom up coil — Resistance too low	blocking fault
23-21	Primary boom down coil — Valve status fault	blocking fault
23-25	Primary boom down coil — Resistance too high	blocking fault
23-26	Primary boom down coil — Resistance too low	blocking fault
24-08	Primary boom angle — Component fault	blocking fault
24-13	Primary boom angle — Not detected	blocking fault
24-14	Primary boom angle — Cross check fault	blocking fault
24-17	Primary boom angle — Not calibrated	blocking fault
24-19	Primary boom angle — Out of range	blocking fault
24-22	Primary boom angle — Value not changing	blocking fault
24-30	Primary boom angle — Calibration mismatch	blocking fault
25-21	Cable tension — Fault	blocking fault
26-21	Primary boom extend coil — Valve status fault	blocking fault
27-21	Primary boom retract coil — Valve status fault	blocking fault
35-27	Ground Control Station Buttons — Active at startup	warning / function limited
36-21	Jib up coil — Fault	blocking fault
36-25	Jib up coil — Resistance too high	blocking fault
36-26	Jib up coil — Resistance too low	blocking fault
37-21	Jib down coil — Fault	blocking fault
37-25	Jib down coil — Resistance too high	blocking fault
37-26	Jib down coil — Resistance too low	blocking fault
41-11	Turntable rotate joystick — Shorted to supply	blocking fault
41-16	Turntable rotate joystick — Value at 0 V	blocking fault
41-17	Turntable rotate joystick — Not calibrated	blocking fault
42-21	Turntable rotate CW coil — Valve status fault	blocking fault
43-21	Turntable Rotate CCW Coil — Valve status fault	blocking fault
43-25	Turntable Rotate CCW Coil — Resistance too high	blocking fault
43-26	Turntable Rotate CCW Coil — Resistance too low	blocking fault
44-27	Drive enable toggle switch — Active at startup	blocking fault
46-21	Platform Rotate CW Coil — Fault	blocking fault
46-25	Platform Rotate CW Coil — Resistance too high	blocking fault
46-26	Platform Rotate CW Coil — Resistance too low	blocking fault
47-21	Platform rotate CCW coil — Fault	blocking fault
47-25	Platform rotate CCW coil — Resistance too high	blocking fault
47-26	Platform rotate CCW coil — Resistance too low	blocking fault
51-11	Drive joystick — Shorted to supply	blocking fault
51-16	Drive joystick — Value at 0 V	blocking fault
51-17	Drive joystick — Not calibrated	blocking fault
61-11	Steer joystick — Shorted to supply	blocking fault
61-16	Steer joystick — Value at 0 V	blocking fault
61-17	Steer joystick — Not calibrated	blocking fault
64-11	Hydraulic pressure sensor — Shorted to supply	warning / function limited
64-16	Hydraulic pressure sensor — Value at 0 V	warning / function limited
64-17	Hydraulic pressure sensor — Not calibrated	warning / function limited
68-27	Function enable toggle switch — Active at startup	blocking fault
68-28	Function enable toggle switch — Time out	warning / function limited
71-21	Emergency Stop relay — Fault	blocking fault
72-14	Lift guard contact alarm switch — Cross check fault	blocking fault
76-13	Platform load sensor — Not detected	blocking fault
76-14	Platform load sensor — Cross check fault	blocking fault
76-15	Platform load sensor — Value too low	blocking fault
76-17	Platform load sensor — Not calibrated	blocking fault
76-21	Platform load sensor — Internal fault	blocking fault
76-23	Platform load sensor — Value too high	blocking fault
76-31	Platform load sensor — Invalid setup	blocking fault
77-13	Platform display (VCON) — Not detected	warning / function limited
77-29	Platform display (VCON) — Software version mismatch	blocking fault
78-13	Platform controller (PCON) — Not detected	blocking fault
78-29	Platform controller (PCON) — Software version mismatch	blocking fault
79-13	Ground display (DISCON) — Not detected	warning / function limited
79-29	Ground display (DISCON) — Software version mismatch	blocking fault
80-21	Turntable controller (TCON) — Fault	blocking fault
82-21	Load sense recovery — Fault	warning / function limited
83-20	Disabled by owner — Warning	blocking fault
84-13	Chassis angle (Primary) — Not detected	blocking fault
84-14	Chassis angle (Primary) — Cross check fault	blocking fault
84-17	Chassis angle (Primary) — Not calibrated	blocking fault
84-21	Chassis angle (Primary) — Fault	blocking fault
85-13	Chassis angle safety (Secondary) — Not detected	blocking fault
85-17	Chassis angle safety (Secondary) — Not calibrated	blocking fault
85-21	Chassis angle safety (Secondary) — Fault	blocking fault
89-12	Fuel level — Value too high	warning / function limited
89-16	Fuel level — Value at 0 V	warning / function limited
92-21	Turntable rotate flow coil — Fault	blocking fault
92-25	Turntable rotate flow coil — Resistance too high	blocking fault
92-26	Turntable rotate flow coil — Resistance too low	blocking fault
94-13	Primary boom length — Not detected	blocking fault
94-14	Primary boom length — Cross check fault	blocking fault
94-17	Primary boom length — Not calibrated	blocking fault
94-19	Primary boom length — Out of range	blocking fault
94-22	Primary boom length — Value not changing	blocking fault
94-30	Primary boom length — Calibration mismatch	blocking fault
95-23	Engine RPM — Too high	warning / function limited
95-24	Engine RPM — Too low	warning / function limited
96-19	Low oil pressure or engine overtemp — Out of range	blocking fault
97-21	Drive motor speed — Fault	blocking fault
98-08	Platform level angle — Component fault	blocking fault
98-10	Platform level angle — Envelope exceeded	blocking fault
98-13	Platform level angle — Not detected	blocking fault
98-14	Platform level angle — Cross check fault	blocking fault
98-17	Platform level angle — Not calibrated	blocking fault
98-19	Platform level angle — Out of range	blocking fault
98-22	Platform level angle — Value not changing	blocking fault
98-30	Platform level angle — Calibration mismatch	blocking fault
99-21	Primary boom extend/retract flow coil — Fault	blocking fault
99-25	Primary boom extend/retract flow coil — Resistance too high	blocking fault
99-26	Primary boom extend/retract flow coil — Resistance too low	blocking fault
100-21	Platform level up coil — Fault	blocking fault
100-25	Platform level up coil — Resistance too high	blocking fault
100-26	Platform level up coil — Resistance too low	blocking fault
101-21	Platform level down coil — Fault	blocking fault
101-25	Platform level down coil — Resistance too high	blocking fault
101-26	Platform level down coil — Resistance too low	blocking fault
104-11	Front steer angle — Shorted to supply	warning / function limited
104-16	Front steer angle — Value at 0 V	warning / function limited
104-17	Front steer angle — Not calibrated	warning / function limited
116-20	Model configuration — Warning	warning / function limited
116-31	Model configuration — Invalid setup	blocking fault
130-23	Battery current — Too high	blocking fault
131-23	Battery voltage — Too high	blocking fault
131-24	Battery voltage — Too low	blocking fault
135-08	Wall powered charger — Component fault	warning / function limited
135-13	Wall powered charger — Not detected	warning / function limited
135-28	Wall powered charger — Charge timeout	warning / function limited
135-29	Wall powered charger — Software version mismatch	blocking fault
136-08	Pump motor controller 1 — Component fault	blocking fault
136-13	Pump motor controller 1 — Not detected	blocking fault
137-08	Left front AC drive controller — Component fault	blocking fault
137-13	Left front AC drive controller — Not detected	blocking fault
138-08	Right front AC drive controller — Component fault	blocking fault
138-13	Right front AC drive controller — Not detected	blocking fault
139-08	Left rear AC drive controller — Component fault	blocking fault
139-13	Left rear AC drive controller — Not detected	blocking fault
140-08	Right rear AC drive controller — Component fault	blocking fault
140-13	Right rear AC drive controller — Not detected	blocking fault
142-10	Primary boom maximum angle safety (PBMAS) — Envelope exceeded	blocking fault
143-10	Primary boom maximum length safety (PBMLS) — Envelope exceeded	blocking fault
148-21	Sensor Power P85PWR — Fault	blocking fault
149-09	Sensor Power P109PWR — Shorted to 0V	blocking fault
149-11	Sensor Power P109PWR — Shorted to Supply Voltage	blocking fault
149-23	Sensor Power P109PWR — Value too high	blocking fault
149-24	Sensor Power P109PWR — Value too low	blocking fault
152-21	Primary Down On/Off Valve — Valve status fault	blocking fault
189-25	Lift Pump Motor 1 — Resistance Too High	blocking fault
190-25	RR Drive Motor — Resistance Too High	blocking fault
191-25	LR Drive Motor — Resistance Too High	blocking fault
192-25	RF Drive Motor — Resistance Too High	blocking fault
193-25	LF Drive Motor — Resistance Too High	blocking fault
194-21	RR Brake Coil — Fault	blocking fault
195-21	LR Brake Coil — Fault	blocking fault
196-21	RF Brake Coil — Fault	blocking fault
197-21	LF Brake Coil — Fault	blocking fault
198-21	RR Speed Sensor — Fault	blocking fault
199-21	LR Speed Sensor — Fault	blocking fault
200-21	RF Speed Sensor — Fault	blocking fault
201-21	LF Speed Sensor — Fault	blocking fault
204-21	Main Battery — Fault	blocking fault
205-21	Drive Power Contactor — Fault	blocking fault
205-27	Drive Power Contactor — Active ON at Start Up	blocking fault
233-19	Battery Temperature — Out of Range	blocking fault
233-21	Battery Temperature — Fault	blocking fault
233-23	Battery Temperature — Too High	blocking fault
233-24	Battery Temperature — Too Low	blocking fault
252-13	Battery Management System (BMS) — No Response	blocking fault
252-21	Battery Management System (BMS) — Component Fault	blocking fault
253-21	Capacitor Charge — Fault	blocking fault
254-23	Battery Charge Voltage — Too High	warning / function limited
254-24	Battery Charge Voltage — Too Low	warning / function limited
255-20	Right Rear Drive Motor Temperature — Warning	warning / function limited
255-21	Right Rear Drive Motor Temperature — Fault	blocking fault
256-20	Left Rear Drive Motor Temperature — Warning	warning / function limited
256-21	Left Rear Drive Motor Temperature — Fault	blocking fault
257-20	Right Front Drive Motor Temperature — Warning	warning / function limited
257-21	Right Front Drive Motor Temperature — Fault	blocking fault
258-20	Left Front Drive Motor Temperature — Warning	warning / function limited
258-21	Left Front Drive Motor Temperature — Fault	blocking fault
259-20	Right Rear Drive Controller Temperature — Warning	warning / function limited
259-23	Right Rear Drive Controller Temperature — Too High	blocking fault
259-24	Right Rear Drive Controller Temperature — Too Low	blocking fault
260-20	Left Rear Drive Controller Temperature — Warning	warning / function limited
260-23	Left Rear Drive Controller Temperature — Too High	blocking fault
260-24	Left Rear Drive Controller Temperature — Too Low	blocking fault
261-20	Right Front Drive Controller Temperature — Warning	warning / function limited
261-23	Right Front Drive Controller Temperature — Too High	blocking fault
261-24	Right Front Drive Controller Temperature — Too Low	blocking fault
262-20	Left Font Drive Controller Temperature — Warning	warning / function limited
262-23	Left Font Drive Controller Temperature — Too High	blocking fault
262-24	Left Font Drive Controller Temperature — Too Low	blocking fault
264-23	Amp Hour Return — Too High	warning / function limited
265-21	Charger USB — Fault	warning / function limited
266-21	Charge Profile — Fault	blocking fault
266-31	Charge Profile — Setup Invalid	blocking fault
267-23	Charger AC Voltage — Too High	blocking fault
267-24	Charger AC Voltage — Too Low	blocking fault
268-21	Charger Cooling Fan — Fault	warning / function limited
270-21	Pump Controller 1 Contactor — Fault	blocking fault
270-27	Pump Controller 1 Contactor — Active at Startup	blocking fault
271-21	Pump Motor 1 Temperature — Fault	blocking fault
271-23	Pump Motor 1 Temperature — Too High	warning / function limited
272-20	Pump Controller 1 Temperature — Warning	warning / function limited
272-23	Pump Controller 1 Temperature — Too High	blocking fault
272-24	Pump Controller 1 Temperature — Too Low	blocking fault
273-21	Pump Motor 1 Speed Sensor — Fault	blocking fault
274-08	Pump Motor Controller 2 — Component Fault	blocking fault
274-13	Pump Motor Controller 2 — No Response	blocking fault
274-31	Pump Motor Controller 2 — Setup Invalid	blocking fault
275-21	Pump Controller 2 Contactor — Fault	blocking fault
275-27	Pump Controller 2 Contactor — Active at Startup	blocking fault
276-20	Pump Controller 2 Temperature — Warning	warning / function limited
276-23	Pump Controller 2 Temperature — Too High	blocking fault
276-24	Pump Controller 2 Temperature — Too Low	blocking fault
277-21	Pump Motor 2 Temperature — Fault	blocking fault
277-23	Pump Motor 2 Temperature — Too High	warning / function limited
278-21	Pump Motor 2 Speed Sensor — Fault	blocking fault
279-08	Welder Motor Controller — Component Fault	blocking fault
279-13	Welder Motor Controller — No Response	blocking fault
280-21	Welder Controller Contactor — Fault	blocking fault
280-27	Welder Controller Contactor — Active at Startup	blocking fault
281-23	Welder Controller Temperature — Too High	blocking fault
281-24	Welder Controller Temperature — Too Low	blocking fault
282-21	Welder Motor Temperature — Fault	blocking fault
282-23	Welder Motor Temperature — Too High	warning / function limited
283-21	Welder Motor Speed Sensor — Fault	blocking fault
284-25	Proportional Relief 2 Coil — Resistance Too High	blocking fault
284-26	Proportional Relief 2 Coil — Resistance Too Low	blocking fault
285-25	Proportional Relief 3 Coil — Resistance Too High	blocking fault
285-26	Proportional Relief 3 Coil — Resistance Too Low	blocking fault
286-21	Lift Pump Motor 2 — Fault	blocking fault
286-25	Lift Pump Motor 2 — Resistance Too High	blocking fault
287-21	Welder Motor — Fault	blocking fault
287-25	Welder Motor — Resistance Too High	blocking fault
288-9	P198 Sensor Power — Shorted to 0V	blocking fault
288-11	P198 Sensor Power — Shorted to Supply Voltage	blocking fault
288-23	P198 Sensor Power — Too High	blocking fault
288-24	P198 Sensor Power — Too Low	blocking fault
289-23	TCON System Power — Too High	blocking fault
289-24	TCON System Power — Too Low	blocking fault
290-23	PCON System Power — Too High	blocking fault
290-24	PCON System Power — Too Low	blocking fault
291-27	Platform Control Buttons — Active at Startup	blocking fault
292-17	Hydraulic Pump 1 — Not Calibrated	warning / function limited
293-17	Hydraulic Pump 2 — Not Calibrated	warning / function limited
294-17	Hydraulic Pump 3 — Not Calibrated	warning / function limited