609 609 105609 609 104

Genie error codes

Genie S-85 XC FE/E, S-60 DC, Z-60 DC: drive motor controllers

These are codes of the electric drive motor controllers (hexadecimal notation, e.g. 0x2510), separate from the machine control codes. Below are 107 codes with the original message from the manufacturer's manual and its description. They apply to these machines: Genie S-85 XC FE, S-85 XC E, S-60 DC, Z-60 DC. Source: Genie Service and Repair Manuals (Part No. 1337498, 1307785, 1299608), drive controller code table.

Showing the first 30: type more digits of the code.

The descriptions are quoted from the manufacturer's service documentation and are for guidance only. Clearing codes, calibrations and repairs are carried out by a qualified service technician according to the manual for the specific serial number. A machine with an active blocking code must not be used until the cause has been removed.

All Genie codes: the list

CodeMeaningType
0x2510Controller Overcurrentblocking fault
0x2832Current Sensor Faultblocking fault
0x2223Precharge Failedblocking fault
0x2141Controller Severe Undertempblocking fault
0x2142Controller Severe Overtempblocking fault
0x2120Severe B+ Undervoltageblocking fault
0x2122Severe KSI Undervoltageblocking fault
0x2130Severe B+ Overvoltageblocking fault
0x2132Severe KSI Overvoltageblocking fault
0x2133Speed Limit Supervisionblocking fault
0x2134Travel Control Supervisionblocking fault
0x2109Critical OS General Fault Program execution within the controller encountered a critical problem and could not recover from this.blocking fault
0x210AOS General 2 Fault Program execution within the controller encountered a serious problem and could not recover from this.blocking fault
0x2110Reset Rejectedblocking fault
0x2140Controller Overtemp Cutbackwarning / function limited
0x2121Undervoltage Cutbackwarning / function limited
0x2131Overvoltage Cutbackwarning / function limited
0x2531Ext 5V Supply Failure Ext 5V Supply Failure Active _ _ _ _ 0x2531 Fault Type(s):blocking fault
0x2532Ext 12V Supply Failure Fault Type(s):blocking fault
0x2151Motor Temp Hot Cutbackwarning / function limited
0x2150Motor Temp Sensorwarning / function limited
0x2222Main Driver Fault Type(s):blocking fault
0x2320EM Brake Driver Fault Type(s):blocking fault
0x2232Sin Cos Motor Feedback 1. The signals from the sensor are above the configuration by 10% or at/above the supply rails for >100ms. 2. Sensor failure.blocking fault
0x2230Encoder Fault Fault Type(s):blocking fault
0x2240Motor Open Faultblocking fault
0x2220Main Contactor Weldedblocking fault
0x2221Main Contactor Did Not Close Fault Type(s):blocking fault
0x2103Motor Setup Needed Fault Type(s): Hex # Bit1 – 4 Binary 0000 => bits 4 3 2 1blocking fault
0x2102Motor Misalignment Errorblocking fault
0x2830NV Memory Failure Fault Type(s):blocking fault
0x2211HPD Sequencingwarning / function limited
0x2460Emergency Reverse High Pedal HPDwarning / function limited
0x2813Parameter Change Fault Type(s): Reports the CAN Object ID of parameter.blocking fault
0x2710User 1 Fault Global Drive Shutdownblocking fault
0x2711User 2 Fault Internal CAN communication errorblocking fault
0x2712User 3 Fault Invalid Motor Type Selectionblocking fault
0x2713User 4 Fault Front to Back CAN bus faultblocking fault
0x2820VCL Run Time Errorblocking fault
0x2831Internal Controller Faultblocking fault
0x2541PDO Timeoutblocking fault
0x2231Stall Detectedblocking fault
0x2550Insulation Resistance Too Lowwarning / function limited
0x2840Supervision Faultblocking fault
0x2841Supervision Input Checkblocking fault
0x2542PDO Mapping Errorblocking fault
0x2835Internal Hardware Faultblocking fault
0x2850Motor Characterization Errorblocking fault
0x2234Encoder Pulse Errorblocking fault
0x2811Parameter Out of Range Fault Type(s): Reports the CAN Object ID of parameter.blocking fault
0x2815Bad Firmwareblocking fault
0x2321EM Brake Failed To Setblocking fault
0x2233Encoder Limited Operating Strategy (LOS)warning / function limited
0x2520Pump Overcurrentblocking fault
0x2450Pump Battery Discharge Indicator (BDI)warning / function limited
0x2833Pump Hardware Error Fault Type(s):blocking fault
0x2812Parameter Mismatchblocking fault
0x2332Interlock Braking Supervision Fault Type(s):1 = Motor speed is outside the Interlock Brake Supervision Speed Limit.blocking fault
0x2160Driver 1 Fault Fault Type(s):blocking fault
0x2161Driver 2 Fault Fault Type(s): See Driver 1 Faultblocking fault
0x2162Driver 3 Fault Fault Type(s): See Driver 1 Faultblocking fault
0x2163Driver 4 Fault Fault Type(s): See Driver 1 Faultblocking fault
0x2164Driver 5 Fault Fault Type(s): See Driver 1 Faultblocking fault
0x2165Driver 6 Fault Fault Type(s): See Driver 1 Faultblocking fault
0x2166Driver 7 Fault Fault Type(s): See Driver 1 Faultblocking fault
0x2632Driver Assignment Fault Type(s): 5 {X} = Driver number that cause the fault.blocking fault
0x2169Coil Supply Fault Fault Type(s):blocking fault
0x2620Analog 1/ Pin 16 Out of Range Fault Type(s):blocking fault
0x2621See Analog 2 / Pin 8 Out of Rangeblocking fault
0x2622See Analog 3 / Pin 31 Out of Rangeblocking fault
0x2623See Analog 4 / Pin 32 Out of Rangeblocking fault
0x2624See Analog 5 / in 9 Out of Rangeblocking fault
0x2625See Analog 6 / Pin 15 Out of Rangeblocking fault
0x2626See Analog 7 / Pin 22 Out of Rangeblocking fault
0x2627See Analog 8 / Pin 28 Out of Rangeblocking fault
0x2628See Analog 9 / Pin 24 Out of Rangeblocking fault
0x262ASee Analog 14 / Pin 14 Out of Rangeblocking fault
0x2631Analog Assignment Fault Fault Type(s): 13 X = Analog Input number that caused the fault. {X = 1-9, 14, 18- 19, 31}warning / function limited
0x262BSee Analog 18 / Pin 27 Out of Rangeblocking fault
0x262CSee Analog 19 Out of Rangeblocking fault
0x2834Pump Current Sensor Fault Sensor zero- current offset close to supply voltage or sensor (supply) ground.blocking fault
0x2860Branding Errorblocking fault
0x2106Analog 31 Out of Range / Pin 26blocking fault
0x2108VCL Watchdog The time interval of the VCL watchdog (WD#) exceeded the timeout value.blocking fault
0x2111Autobaud Failure on linked controller CAN portwarning / function limited
0x2113Primary State Errorwarning / function limited
0x2870Hardware Compatibilityblocking fault
0x211AMotor Bracking Impairedblocking fault
0x211CHazardous Movement 1blocking fault
0x212AMemory Parity An internal memory error occurred. Fault Type: Indicates in which memory or peripheral the fault occurred.blocking fault
0x2250Dual Severe A severe failure has on either of the controllers setup for dual drive.blocking fault
0x2253Dual PDO Timeout The time between DD CAN PDO messages received exceeded the PDO Timeout period (52ms). Fault Type(s): 1blocking fault
0x2330EMER Rev Timeout Emergency Reverse was activated and ran until the EMR Timeout timer expired. Fault Type(s): 1blocking fault
0x2331EMER REV HPD At the conclusion of Emergency Reverse, the fault was set because various inputs were not returned to neutral. Fault Type(s): 1warning / function limited
0x2333EMER Supervision During an EMR event, the motor speed exceeded the limit set by the Emergency Reverse Supervision parameters. Fault Type(s): 1blocking fault
0x2871ECC Run Time Error An embedded C application has encountered a runtime error. Fault Type(s)blocking fault
0x2890ERU Configuration Bad configuration for EXISEL in the ERU.blocking fault
0x2891Desat Trip DESAT trip detected. Fault flags(s): 0x01 = U phase. 0x02 = U phase. 0x04 = V phase. 0x08 = V phase. 0x10 = W phase. 0x20 = W phase.blocking fault
0x2420PUMP DRIVER FAULTblocking fault
0x22A2Interlock Input Conflictblocking fault
0x2880PWM DRIVER COUNTblocking fault
0x2629PWM INPUT 10 OUT OF RANGEwarning / function limited
0x262DPWM INPUT 17 OUT OF RANGEwarning / function limited
0x2107INVALID CAN PORTblocking fault
0x210CPWM INPUT 28 OUT OF RANGEwarning / function limited
0x210DPWM INPUT 29 OUT OF RANGEwarning / function limited
0x2101PHASE PWM MISMATCHblocking fault